If you attach the ukulele neck directly to the 8" hand drum, it won't work, you'll have to put the banjo bridge too near from the tambourine border in order to get a proper intonation. In the case of the wooden dowel, the dowel is joined to the neck using a tenon and the neck/dowel is held securely to the rim with a brace. Even if the rest of the neck is excited perfectly, this cut can make or break an otherwise great banjo. I used a block of hard wood and shaped in to fit the neck heel one side and the hand drum the other side. Make it about 24–26 inches (61.0–66.0 cm) long, tapered from 3 1 ⁄ 2 inches (8.9 cm) on one end to about 1 1 ⁄ 2 inches (3.8 cm) on the other. Make a line parallel to the fingerboard surface. Mark the back side of the neck heel by measuring up from the line just marked about 3″. In fact, this banjo neck was made by me in my shop and the heel was hand cut by me specifically for this article. The banjo neck used in this example was already shaped and the heel wasn’t cut at all. In order to make a "typical" banjo neck out of a block of solid wood, you would need a block about 3 1/2" wide, 3" thick, and 28" long, and just to give yourself a little elbow room, you might want something a bit larger. Add between 5 and 7 inches to accommodate for the length of the peghead. Bevel the last two inches of the opposite end to attach … THE SOLUTION : making the neck longer. Maple can either be soft maple or rock maple. Now let’s layout the peghead. Waiting allows the … In order to make a "typical" banjo neck out of a block of solid wood, you would need a block about 3 1/2" wide, 3" thick, and 28" long, and just to give yourself a little elbow room, you might want something a bit larger. It is best to wait for this part of the job until the rim has been turned on the lathe. In the pattern shown here, the peghead meets the fingerboard at about 7 degrees. Watch Promo Enroll in Course × off original price! How to Make a Banjo Neck Step-By-Step. This also allows us to adjust our radius and angle a little bit. Some banjos even have two steel rods that may be adjusted to change the neck angle. Cut your banjo's neck from a piece of 2X4 lumber. In any case the dowel stick accomplishes its job by mounting to the tail of the banjo rim and by attaching to the neck. The ears are added; The peghead overlay and fingerboard are added. The plane of the peghead must tilt back from the plane of the fingerboard at about 7 degrees. After making the templates and the neck blank with the slot for the truss rod, the next step was to cut the angle for the peg head and the curved, angled cut where the neck meets the pot (body) of the banjo. The pivot is 5.5" from the blade to create the 11" diameter cut. After threading the bolts into the end of the neck, temporarily join the neck to the rum with the rim rods. Then, bore the hanger-bolt pilot holes. I have also done the job by hand with a piece of sand paper attached to the waste cut off the heel of the neck. Use a protractor to find the angle. Click on the pictures for larger view. How To Make A Banjo - Online Course In this course I'm going to teach you everything you need to know to build the exact banjos that i build and sell. After cutting the banjo neck heel radius with the band saw a sanding wheel jig may be used to get all the saw marks off the heel of the neck. There are a variety of ways that the heel of a banjo neck can taper into the handle portion of the neck, I use a gentle inside curve. Workpieces are trued on the jointer; Gluing (if two piece neck) The side profile is cut out, then the neck blank is left to cure a while. Attach this to the sound box through one of the blocking spacers you have previously added, using heavy wood screws pre-drilled through the sound box. This is the jig we made for the curved angled cut.. Any one of several woods can be used to make a banjo although maple seems to be the most common. The neck heel dowel stick hole is drilled. Any one of several woods can be used to make a banjo although maple seems to be the most common. The coupon code you entered is expired or invalid, but the course is still available! The neck is reinforced. Mark a straight line that is the intended length of the fingerboard. With the tone ring and flange temporarily in place on the rim, hold the neck in position, and use a drill bit to mark the end of the neck for the hanger bolts. The neck heel radius is cut. This line is the length of the fingerboard. A completely blank neck is pretty intimidating. The peghead …